EN
User Guide
TRC458
CRAWLER
Model: TRC 458
Version: EN.1.00.422
2
Dirty Water Outlet ......................................................................................... 22
Stove Use ..................................................................................................... 22
Using the Cassette Toilet ............................................................................. 23
Crawler S mart Panel .................................................................................. 24
Diesel Heater................................................................................................ 29
Truma Combi ................................................................................................ 30
Crane ............................................................................................................ 52
Victron Energy Battery.................................................................................. 54
Schmid Solar Panel 325w 8ı Regulator ....................................................... 55
Thule Electric Step ....................................................................................... 56
Mover............................................................................................................ 57
Technical Specifications ............................................................................... 60
Electric scheme ............................................................................................ 61
Care Instructions .......................................................................................... 62
Warranty Text ............................................................................................... 64
Warranty Form.............................................................................................. 65
Basic Warnings ............................................................................................ 4
Safety .......................................................................................................... 6
Equipment List............................................................................................. 11
Living and Sleeping Area ............................................................................ 11
Interior Kitchen Area .................................................................................... 11
Bathroom/ Toilet ......................................................................................... 11
Electrical/ Control Installation ...................................................................... 12
Gas Pipe System ......................................................................................... 12
Water Pipe System...................................................................................... 12
Optional Features ........................................................................................ 12
Schematic Explanation ................................................................................ 13
Use of TRC 458 ........................................................................................... 14
Separating the Caravan from the Vehicle ................................................... 14
Using the Fixing Feet .................................................................................. 14
Opening the Entry Door............................................................................... 15
Using the Spare Wheel ............................................................................... 15
Using Kitchen Back Cover and Cabinet Locks ........................................... 16
Using the Electric Step ................................................................................ 16
Using Windows............................................................................................ 17
Use of the Seating and Sleeping Area ........................................................ 17
Use of Upper Sleeping Area ....................................................................... 18
Using the Side Awning ................................................................................ 18
Use of the Kitchen Area .............................................................................. 19
Using the Moving Table .............................................................................. 19
Use of Dynamic Air Suspension (C.D.S.) ................................................... 20
Refrigerator Usage ...................................................................................... 21
Battery/ Sink Usage .................................................................................... 21
Clean Water Inlet ......................................................................................... 21
CRAWLER
Model: TRC 458
Version: EN.1.00.422
3
Use the user guide to access specific information and familiarize yourself with your caravan’s functions.
In addition to standard equipment, this manual also describes optional equipment or accessories.
This user manual helps you to enjoy your TRC 458 as best as possible. It also contains important information that concerns the safety of you and other users.
Thanks for choosing CRAWLER!
* Certain countries may have legal requirements that affect the level of equipment.
* CRAWLER continues its continuous product development efforts to provide a better experience. Features, designs and illustrations in the user manual are not
binding. CRAWLER reserves the right to make changes without prior notice.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
4
Things to consider while traveling;
- For safety reasons, do not exceed the legal speed limit of 80 km/h, even if
the speed limit in some countries is higher.
- When descending long and steep slopes, the brake is loaded more than
normal. Shift to a lower gear and adjust your speed.
- Shift to a lower gear and adjust your speed.
In order to avoid situations such as loss of balance, injury and accident, there
should be no living creatures in the caravan while traveling (people, pets, etc.).
- Do not keep flammable and explosive materials in the caravan.
- Make sure breakable items are secured inside the caravan.
- Pay attention to the approach angle between the vehicle and the caravan
when reversing.
- Caravans equipped with air suspension (CD.S.) are recommended to be
used in road mode and with the compressor on.
- Pay attention to the height of the caravan (2.50 m) at the parking garage
and garage entrances.
- Periodic maintenance of vehicles with air suspension and air tank should be
done regularly. Unmaintained equipment can cause malfunction, injury,
accident and property damage.
Basic Warnings
Things to check before setting off;
- Adjust the pilot wheel to the vehicle's drawbar height.
- Make sure the coupling and stabilizer are in the open position.
- Make sure the pilot wheel is assembled.
- Position the coupling to engage the vehicle's drawbar and lower the pilot
wheel in this position.
- Raise the pilot wheel again to check the connection, the rise of the vehicle
and the TRC 458 together indicates that the connection is secure and correct.
- After connecting the caravan to the vehicle, make sure to collect the pilot
wheel and the handbrake is released.
- Make sure the gas valve is closed.
- Make sure doors and cabinets are locked.
- Make sure the fixing feet are in the closed position.
- Make sure the awning and outside shower area are closed and locked.
- Make sure the spare wheel is locked.
- Fragile items should be placed inside the cabinets.
- Make sure the battery is full.
- Make sure the pop-up roof is locked from the inside.
- Make sure taps and valves are closed.
- Make sure the windows are closed and locked.
- Check your tire pressures.
- Check the charge status of the battery.
- Make sure the movable table is fixed.
- Check the lighting system.
- Load the caravan by keeping the weight balance in mind.
- Open the pop-up tent windows before closing the bed part.
- Be sure to use the caravan in road mode while driving.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
5
Things to consider while camping;
- Before separating the caravan from your vehicle, make sure that the parking
brake is applied.
- Before raising the pilot wheel, make sure that the fixing feet are in the open
position.
- When the indicator next to the cassette toilet turns red, remove the cassette
from the area on the front cover and empty it to the appropriate places.
- Check the fullness of the dirty water tank and empty it to legally appropriate
places before it reaches 100% fullness.
- It is recommended not to use the awning in strong wind conditions.
- Keep the gas valves closed when the stove is not in use.
- Make sure the solar panel surface is clean.
- Be sure to secure with the spare wheel carrier in the open position.
- It is recommended to use propane-added tubes in order to prevent the tube
from freezing in cold weather and to use the tube-operated devices effectively.
- For diesel heater use, make sure the fuel tank is full.
- For clean water use make sure the water tank is full.
- Pay attention to the load balance in the caravan living area when the vehicle
is on the outriggers in the camping position. All users staying in the same area
may destabilize the vehicle.
- The rear bins at the back of the caravan should not be approached with fire
and flammable materials. It may cause injury and fire.
- Care should be taken when using the ladder to the upper bed against the
risk of falling and slipping, and adult control is recommended for children's use.
- The awning should be opened at certain intervals and ventilated.
Things to consider while parked;
- Make sure the handbrake is engaged.
- It is recommended to park the TRC 458 on level ground.
- Make sure doors, windows, cabinets, spare wheel and awning are closed
and locked.
- Make sure the pop-up roof is closed.
- In case of long-term parking in winter, empty the dirty water tanks and the
clean water tank so that there is no water in the booster.
- In case of long-term parking, keep the main switch off.
- It is recommended to take a safety precaution by using a coupling lock.
- Do not leave flammable or explosive materials inside TRC 458.
- It is recommended that you do not leave products in the refrigerator when
you are not using the TRC 458.
- Make sure the gas valve is closed.
- It is recommended to ventilate the inside of TRC 458 at regular intervals.
- Provide external cleaning of TRC 458 at regular intervals.
- All equipment should be in the standard position when the caravan is parked.
Subsequent changes may cause the settings to be corrupted.
- After using the awning in rainy weather, the awning should be dried and
collected.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
6
Mold
Mold and mildew spores are present in indoor and outdoor environments. In
order to keep all mold and mildew spores under control, check humidity and
ventilate your caravan regularly. A healthy ventilation should be provided to
control humidity.
Chemical Sensitivity
Immediately after the caravan is purchased, and sometimes after a long period
of inactivity, a strong odor and/or chemical sensitivity may be experienced. It's
not a fault of the caravan. As in homes, many different products are used in
the construction of caravans, such as carpet, linoleum, plywood, insulation,
flooring. In the use of different materials, odor sensitivity is more obvious.
Since the caravan has small living spaces, the air exchange inside is
significantly less than the house.
These products can outgas different chemicals, including formaldehyde, when
new or when exposed to high temperatures and/or humidity. This outgassing,
along with minimal air exchange, can cause irritation of the eyes, nose, and
throat, and sometimes headaches, nausea, and various asthma-like
symptoms. The elderly and young children, as well as anyone with asthma,
allergies or lung problems, may be more sensitive to the effects of gassing.
Safety
Passenger Transportation
Since there is no seat belt in the caravan, it should not be traveled in the
caravan while driving in order to balance the weight distribution.
Pull and Weight Distribution
Weight distribution is an important factor when loading your camper before
travelling. An evenly distributed caravan will result in efficient and trouble-free
towing.
In order for the caravan to be able to go out on the road in a healthy way and
not to sway, especially on bends, the center of gravity should be spread inside
the caravan, not on one side.
Swinging Control
Swinging or fishtail is the sideways movement of the caravan caused by
external forces. Excessive rocking of your camper can cause the caravan and
towing vehicle to topple over, resulting in serious injury or death.
Tire Safety
Properly maintained tires improve handling and stopping. The wheel nuts must
be properly tightened.
Tools and Equipment
Appliances (stove, refrigerator, etc.) and equipment (hot water heater, oven,
etc.) typically run on LPG. LPG is flammable and is under high pressure.
Misuse may cause fire and/or explosion. Be sure to follow all instructions and
warnings in the manual, as well as in the device and equipment specific user
manuals.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
7
Low Voltage
The detector's operating voltage is 12 VDC. The voltage supplied to the
detector in the caravan may drop below 8 VDC minimum. The detector gives
the user a low voltage warning before it reaches this level and gives additional
clear warnings and alarms after the 8 VDC level is reached. However, if the
current power supplied to the unit is below the operating voltage of 8 VDC, the
detector will not detect the gas or protect against dangerous LPG levels.
Note
If a low voltage warning sounds, the detector will need to be reset by
disconnecting the battery before normal operation can occur.
Ventilation
It is very important to ventilate the caravan to reduce exposure to chemicals
from outgassing. Ventilation should be done frequently after purchase and
when temperatures and humidity rise. Note that gas output is accelerated by
heat and humidity. Open windows, vents and doors. Use natural ventilation or
a fan to expel stale air and bring in fresh air. Reducing airflow by sealing the
caravan increases the formaldehyde level in the vehicle's interior air.
Do not smoke
Smoking inside the caravan will damage the caravan and also release other
toxic chemicals such as formaldehyde.
Medical Advice
Questions about the effects of formaldehyde on your health should be
addressed to your doctor or local health department.
Alarms and Detectors
LPG/CO Detector
Please read the entire detector manual before operating the unit. The LPG/CO
detector is located in the kitchen area. LPG is a mixture of gases produced
and sold commercially as fuel for heating and cooking appliances. LPG is
highly flammable and as a result can be explosive when ignited under certain
conditions. LPG is heavier than air and will accumulate near the floor if
confined to a confined space. The LPG/CO detector is designed to alarm when
propane gas exceeds 10% of the lower explosive limit for more than 30
seconds or when CO gas reaches unsafe levels. The horn will beep
continuously and the red LED will illuminate when propane gas is detected. If
CO gas is detected, the horn will sound 4 quick chirps followed by a 4 second
pause and the red LED will flash quickly. Your LPG/CO detector is directly
connected to your caravan battery and includes a fuse. There is no separate
internal battery. In normal standby mode, the LED indicator will be green.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
8
Warning
Activation of this detector indicates the possible presence of LPG which could
cause an explosion and/or fire, resulting in serious injury or death. This
normally indicates a leak in the LPG installation or an LPG device. Extinguish
all open flames, open your windows and doors, and evacuate the unit
immediately. Do not use any electrical switches. Turn off the LPG in your gas
tank(s). Do not re-enter your unit until a qualified repair technician has
corrected the problem and confirmed that the system is safe.
Warning
It is not recommended to power off the detector during storage. There is a
small heater in the sensor of the device that burns the dirt in the air during
normal usage periods. During power-off periods, impurities may accumulate
on the sensor. When power is restored to the detector, the detector alarm can
activate until the impurities are burned. This may take several hours, during
which time the alarm will be on continuously.
Warning
After 5 years of use, the detector should be replaced. If it is not changed, it
may not alarm. CO poisoning is popularly known as stove poisoning and can
cause death.
Warning
The device is for general domestic, domestic and caravan use. It cannot be
used in workplaces. It does not meet the required OHS rules. It needs a more
sensitive detector especially for groups at risk for CO poisoning (pregnant
women, patients, etc.).
Warnings
- Carbon Monoxide is produced as a result of incomplete combustion of fuels
such as wood, coal, heating oil, paraffin, gasoline, natural gas, propane,
butane.
- Ideally, it is recommended to install a Carbon Monoxide detector in or near
every room where fuel-burning appliances such as room heaters, water
heaters, stoves, grills are located.
- Ensure that the alarm horn can be heard by everyone it is intended to hear.
Seek medical attention if the caravan user is suspected of being affected by
Carbon Monoxide poisoning.
- If the alarm goes off, be sure to investigate the problem. Ignoring the alarm
could result in illness, injury or death. (CO may be present even if nothing is
seen or smelled by the user.)
- When household cleaning materials are used, room spaces should be well
ventilated as this may cause false alarms.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
9
Avoid dead air spaces as shown!
- Use of a fan to ensure air circulation.
- Leaving cabinets and cabinet doors partially open.
- To help alleviate condensation in cold weather;
- In cold weather keep the temperature reasonably cool as much as
possible.
- The caravan needs to breathe, it will smell when airtight.
- Let some warm air out and outside air in.
- Do not allow humid indoor air to be recycled from use and provide
reasonable ventilation.
Factors Contributing to Mold Growth
For mold growth to occur, indoor or outdoor temperatures must be between
4° and 33°C, and it must also have a source of moisture such as humidity,
stagnant water, moist materials. The fastest growth inside the caravan is due
to its hot and humid condition.
Inhibition of Mold Growth
- Checking relative humidity can prevent mold and mildew growth.
- The use of air conditioners in hot climates will reduce the relative humidity.
- Ventilation is available in the kitchen area.
- To prevent mold growth, using vents when preparing food is an important
factor, even in cold weather.
- Also, opening windows during these activities will help with natural ventilation.
- In extremely humid conditions, using a dehumidifier may help.
- Regular cleaning of mold, which is caused by frequent use of caravan and/or
growing, is an important preventive measure.
- Any spills should be wiped up quickly and dried as soon as possible.
- Avoid leaving damp items lying around.
- On safe surfaces use mold or mildew-killing cleaning products.
- Check the sealing wicks regularly and reseal as necessary to prevent water
leaks.
Proper preventive maintenance of the caravan and its accessories, as
described in both this manual and accompanying literature, will provide the
best protection for the caravan.
Long-Term Use Effects
- In long-term use of caravan, it is necessary to be prepared for condensation
and humid conditions that may be encountered.
- In cold weather, when the relative humidity of the indoor air is high, moisture
may condense on the inner surfaces of caravan. This is exacerbated by the
fact that insulated walls of the caravan are much thinner than house walls.
- The relatively small volume and tight, compact nature of the caravan mean
that even a few passengers' normal living activities will lead to rapid moisture
saturation.
- Water vapor will condense as moisture inside windows and walls, or as frost
or ice in cold weather, unless it is carried outside by ventilation or condensed
with a dehumidifier.
- Inside the walls or ceiling, warped or stained panels can also condense out
of sight.
- The appearance of these conditions can indicate a serious problem. When
signs of excessive humidity and condensation appear on the caravan, it is
important to take action to minimize their effects.
Tips for Checking Condensation
Uses where it is important to let excess moisture out:
- Bathroom
- Washing dishes
- Hair drying
- Cooking
CRAWLER
Model: TRC 458
Version: EN.1.00.422
10
Winter Travel
Traveling in sub-freezing temperatures will require certain precautions to
protect the plumbing system and personal belongings from damage by
freezing.
It is necessary to clear the snow accumulations on the pop-up.
Whenever possible the heat should be kept at a constant temperature.
It is easier for the heater to keep the room temperature constant than to let the
caravan temperature drop to 10°C and then try to raise it to room temperature.
When parking in temperatures below freezing, be sure to have a full supply of
LPG or Diesel and plug into a 220V power source whenever possible.
In order to allow hot air to circulate around plumbing lines and fixtures leave
cabinet doors, wardrobes and bedroom doors partially open.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
11
Living and Sleeping Area
6 Person Seating Area
Seat and Back Cushions
Folding Inner Table
Convertible Seats to Sleeping Area (200x160 cm)
Upper Bed Section (200x150 cm)
Interior Kitchen Area
Kitchen Accessible from Inside and Outside
Chrome Kitchen Countertops
Fixed Chrome Kitchen Sink
2 Stove and Pot Holder
Marine Type Chrome Faucet
Kitchen Wardrobes and Drawers
Bathroom/ Toilet
Aluminium Exterior Door
Zippered Premium Interior Door
Compact Laminate Flooring
Thetford Cassette Toilet System
Folding Sink
Shower head
Equipment List
Exterior Design
Alko3004 Stabilizer*
Reflector Triangle (2 Pieces)
Curtain and Mosquito Net Windows on 4 Facades
Side Entry Door
Side WC Entry Door
Back Kitchen Cover
Height Adjustable Fixing Feet (4 Pieces)
Reclining Pop-up Roof System with Openable Window
Chrome Plated Locks Chrome Door Stopper
Wide Angle Chrome Door Hinges
Metal Fuel Can (2x20 L)
Was LED Tail Light *
Was Side Track Lights *
Storage Cabinets
Tube and Storage Cabinets
Outdoor LED Lighting
Interior Design
Ceramic Based Internal Heat Insulation
Electrostatic Powder Coating (Cabinet and Interior
Walls)
Carpet Application on PVC Floor Covering
Item Compartments
Fabric Pocket Set
Side Door Mosquito Net
Shelf Front Zipper Application
Side Door Storage Compartments
Item Organizer with 4 Nodes
Upper Bed Exit Ladder
LED Strip Lighting
USB Charge Inputs
12v Cigarette Lighter Input
CRAWLER
Model: TRC 458
Version: EN.1.00.422
12
Optional Features
Indel B 65 Refrigerator *
Berhimi 50 Refrigerator *
Dometic 65 Refrigerator *
Engel 57 Refrigerator *
Schmid Solar Panel 325w & Regulator *
Leveling Dynamic Air Suspension (CD.S.)
Alko or Winterhoff Coupling Lock *
Truma Mover XT2 *
Headlight Protection Grille (Black)
Crawler 270 Degree Premium Awning (Light Gray)
Chrome Spare Wheel Carrier & Spare Wheel & Premium Outdoor Shower
Gas Output (BBQ)
External Chrome Clean Water Canister
Outdoor Portable Kitchen (Recommended to be purchased with Gas Outlet (BBQ))
Weaponry
Victron Energy 220 Ah Battery (Price Difference) *
Eberspacher D4 Airtronic Space Heater (Diesel) *
Neta Portable Satellite *
Thule Electric Step*
Truma Box Type Air Conditioner *
Truma Combi 4 Ambient & Water Heater *
Truma Boiler (Water Heater)*
Projector Lighting (External Right and Left)
Water Freeze Protection Unit
Come Up Crane or Equivalent (12000Lb) *
Electrical/ Control Installation
13 PIN Socket
6 Analog Control Panel
90 Ah Gel Battery
Remote Controlled and Dimmer Adjustable LED Indoor
Lighting
Victron Blue Smart Charger (10 A)*
Gas Pipe System
Copper Gas Installation
Truma 2 Gas Valve *
Gas Detector
Gas Regulator
Water Pipe System
Water Pump (19 L/Min.)
Water Level Indicator
Chrome White Water Tank (114 L)
Chrome Grey Water Tank (33 L)
Black Water Tank (17 L)
Chrome Water Fill Cap
Water Drain Valves
CRAWLER
Model: TRC 458
Version: EN.1.00.422
13
Schematic Explanation
1. Right and Left Windows with Mosquito Nets and Curtains
2. Side Entry Door
3. Side WC Entry Door
4. Back Kitchen Cover
5. Height Adjustable Fixing Feet (4 Pieces)
6. Openable and Sleeping Area Roof Pop-up System with Window
7. Chrome Plated Locks
8. Fuel Can
9. High Angle Chrome Hinge
10. Spare Wheel
11. Led Tail Light
12. Side Track Lights
13. Storage Cabinets
14. Outdoor LED Lighting
15. Combi / Heater Cabinet
16. Battery Cabinet
17. Step
18. 270 degree Premium Awning
CRAWLER
Model: TRC 458
Version: EN.1.00.422
14
Use of TRC 458
Separating the Caravan from the Vehicle
Pull the handbrake. (1)
Lift the stabilizer up to a vertical position. (2) Lift the coupling arm upwards to
the vertical position. (3) Raise the caravan by turning the pilot wheel lever
counter-clockwise and disconnect the coupling from the vehicle's drawbar.
(4)
Using the Fixing Feet
There are four fixing feet, two at the front and two at the back. Release the
stabilizer foot by pulling the red handle of the stabilizer foot towards you and
move it to the position you want to adjust. Then, adjust the height of the fixing
foot by turning the wheel bolt inside the red handle clockwise with the help of
the wheel wrench inside the caravan.
In order to close the fixing feet, the arm is first inserted into the red pin. It is
rotated. Then the red handle is pulled and the foot is lifted up and fixed in the
up position.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
15
When the rear fixing legs are not opened, there may be an
imbalance in the rear of the caravan due to the weight.
Unlocking the Spare Wheel
In order to unlock the spare wheel on the back of the TRC 458, first remove
the pin (1) from its socket. (2) Bring the lock bolt towards you to the vertical
position. (3) Remove the vehicle rear mount. Move the lock bolt (4) back to
parallel to the spare wheel. (5)
Opening the Entry Door
Top Lock;
Turn the upper lock entry in the horizontal position (1)
counter-clockwise to the vertical position and remove it.
(2)
Bottom Lock;
(3) Turn the vertical lower lock hub clockwise. (4) After the lock bolt is in, turn
the key back to the vertical position and remove it.
To close the spare wheel lock on the back of TRC 458;
First, set the lock bolt to the vertical position.
Replace the vehicle rear mount.
Set the lock bolt parallel to the spare wheel.
Insert the pin into its slot.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
16
Using Kitchen Back Cover and Cabinet Locks
Kitchen Back Cover
The Kitchen Back Cover provides the opportunity to use from inside and
outside. Thanks to the LED strip on the Kitchen Back Cover, the kitchen
section is illuminated.
Cabinet Locks:
First, unlock the caravan by turning it counter-clockwise with its own key. Then
turn the lock lever counter-clockwise to unlock itself.
Using the Electric Step
To turn on the electric step, press and hold the button located at the bottom
left of the entrance in the downward direction. Press and hold upwards to turn
it off.
TURN OFF
TURN ON
Before and after use, it should be checked that the pistons are intact. The cabinet door
should be opened 30-60 cm behind. Otherwise, it may cause injury.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
17
Using Windows
There are three locks on the windows. While unlocking, turn the levers inward
while holding down the red pins. After turning the locks, push the window from
the inside out.
Use of the Seating and Sleeping Area
There are two seats in the sitting area. (1)
There are two USB ports and two cigarette lighter sockets. (2)
There are organizers with fabric pockets at the top of the seating area.
To turn the sitting area into a bed;
The bed set bar is stacked between the seats (3) and the back cushions are
placed on the bed set bar. (4)
Pay attention to the piston when opening the windows. Window
opens and closes from inside to outside!
CRAWLER
Model: TRC 458
Version: EN.1.00.422
18
Use of Upper Sleeping Area
To open the pop-up roof section, release the roof lock (carabiner) and push
the top canopy with the bed upwards. Lower the bed by holding the bed part
so that the ceiling is up. The stairs to the left of the entrance lead to the upper
sleeping area. There are three windows with mosquito nets, one on the front
and one on the sides. Open the mosquito nets according to the need for use.
Gather the opened fabric in rolls and fix it with the Velcro at the bottom. Gently
pull down on the ceiling string to close the roof. Remember to put the lock back
in place and fasten it again.
Using the Side Awning
Open the locks on the side of the awning box, lift the cover of the box upwards.
Open the awning by moving the strap at the beginning of the awning towards
the back of the caravan and fix the strap to the left woodshed. To close it,
retract the legs of the awning in the same way and place it inside the box. Wrap
the hanging fabric in a roll and place it inside the box.
After using the awning in rainy weather, the awning should be dried and
collected. The awning should be opened at certain intervals and ventilated.
Before and after use, it should be checked that the pistons are intact. Pay
attention to the danger of falling while climbing and descending the upper
bed.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
19
Use of the Kitchen Area
The kitchen area provides the possibility of use from the outside and inside.
In the kitchen area, there are countertops, refrigerator, stove, sink, shelves,
kitchenware cabinets and drawers.
There are two valves at the bottom of the kitchen counter.
The water valve (1) on the left is the gas valve on the right.
(2)
Using the Moving Table
To use the moving table;
Unscrew the fixing screw (1) counter-clockwise and lower the table into the
operating position. You can bring the table to the desired position by loosening
the screw (2) located at the bottom of the table. After loosening the screw,
move the table to fix it in the desired position.
The upper bed must be removed during the table opening and closing
process. It should be in the lowest position of the table top when
lowering the upper bed section.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
20
Use of Dynamic Air Suspension (C.D.S.)
Usage Modes:
Road Mode (On-road)
The caravan must be used continuously while in road mode. Push to center
position for use of arms. Levers in the highest (off-road) mode are put into road
mode before normal travel. The compressor switch must be on while traveling.
Off-road Mode
It maximizes the vehicle's traction when driving on difficult terrain and rough
roads. Drive mode provides high ground clearance. It is required for use on
rough terrains when necessary, except for long-term use. The distance
between the rim and the fender is adjusted to 70 cm by moving it up and down
thanks to the air valve rod. When the bar is lowered, the caravan also moves
down.
Camp Mode:
When the caravan leaves the vehicle, it is put into camping mode. Make sure
to turn the levers to the right to lower it into camping mode. Air suspension, in
camping mode, the vehicle can be adjusted to the desired height, left and right,
according to the slope of the terrain.
Setting:
Make sure that all the equipment of the caravan is placed in their standard
positions. Suspension works separately as right and left.
The handles on the left front cabinet of the caravan are turned to the left to
get the highest mode from road mode. (Off-road) (1-2)
When it is turned to the right, it is put into camping mode. It is in road mode
when the levers are in the middle position. (On-road)
Make sure no one is inside the caravan while using the air suspension. Both
bellows should be ideal and in the same position.
Tighten the bellows separately with the help of the clamp to prevent the
setting from changing later. To level the TRC 458 on sloping terrain, you can
level it by changing the height of one side.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
21
What if the battery does not work?
- Pay attention to the water level indicator on the Crawler Smart Panel or
control panel, (see p.28-29-30)
- Check the booster, (see p.28-29-30)
- Check the battery level.
- If there is a problem with the battery, check the user manual of your
battery brand.
Clean Water Inlet
- To fill the clean water tank (114 L) open the clean water inlet by turning it
counter-clockwise with the help of a key.
- Empty the clean water tank from the clean water inlet to the clean water
tank inside.
Lock the lid after filling.
Interior Equipment
Refrigerator Usage
- You can open the refrigerator from inside or outside.
- The opening direction of the cover may vary according to the product
models.
- You can adjust the temperature of the refrigerator with the level-adjusted
cooling feature.
(For detailed information, see the user manual of your refrigerator brand.)
What if the refrigerator does not work?
- Attention is paid to the indicators on the Crawler Smart Panel or Control
Panel.
- Paco switch is opened and closed.
-Battery level is checked.
- If there is a problem with the refrigerator, the user manual of your
refrigerator brand is checked.
Battery/ Sink Usage
- To put it into use, first check the clean water level in the tank.
- Turn on the booster before using the battery.
- You can use the battery from inside and outside thanks to its rotating head.
- When the battery is not in use, it can be kept closed thanks to its foldable
feature.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
22
Stove Use
- First of all, the valve of the tube in the front cabinet of the caravan is
opened in order to open it for use. (1)
- There are two valves inside the cabinet. (2)
- On the right is the gas valve of the stove. (a) The one on the left is its water
heating valve, if there is a boiler system. (b)
- Light the stove with the help of the lighter and adjust the temperature of the
gas coming to the stove with the stove top buttons.
- There is a ventilation system just below the stove.
- When using the combi system, you can adjust the settings from the Truma
Panel.
Dirty Water Outlet
There are two dirty water outlets in the kitchen area (1) and the bathroom (2)
separately.
For the dirty water outlet of the kitchen area;
-The dirty water tank (33 L) is emptied with the help of the valve (1) located in
the left rear cabinet outside of caravan.
For the dirty water outlet of the bathroom area;
- The bathroom drains (2) are emptied directly to the outside.
- When the booster level approaches the critical level, in order to restart the
booster, the drain valve of the dirty water tank should be opened and the tank
should be emptied in an appropriate place, (see p.28-29-30).
- Attention is paid to the booster warnings on the Crawler Smart Panel or the
control panel, (see p.28-29-30)
Thanks to the automatic gas cut-off safety system, the stove turns itself off in
case of emergency. Compatible with LPG & Natural Gas.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
23
Using the Cassette Toilet
Thetford Cassette Toilet
Dimensions: H 534 / W 394 / D 580 mm
Seating Height: 492 mm
Waste Tank Capacity: 18 Liters
Weight: 7.2 Kg
Energy: 12 V
1. Open the toilet seat for use.
2. The seat of the toilet has a 90° swivel feature.
3. Liquids called "caravan toilet chemicals" are poured onto the
tape to break up waste and prevent odor. Pour the toilet
chemical into the tank (3) at scale before use.
4. During use, open the drain by turning the latch (1) in front of
the toilet to the left. Close the drain by turning it to the right after
use.
5. In order not to have to carry the waste tank cassette, it can
be transported more simply with the wheel system and pull
handle (2).
6. When the toilet bowl is full, the indicator next to the toilet will
turn from green to red. (4) The unloading process is done by
sliding and dismounting, thanks to the cover on the front left
cabinet of caravan.
7. After emptying and cleaning, put the cassette section back
and remember to close the lock.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
24
Operations are managed and displayed. The button on the far right with the
"Wheel” symbol provides access to the battery capacity, time and date
adjustment menu, and the menu that provides access to the screen brightness
controls.
Crawler Smart Panel
Crawler Smart Panel is opened by pressing the physical unlock button at the
bottom of its screen once. Each time the physical button is pressed, the system
is restarted. When the screen is opened for the first time, a visual like the
illustration below will appear on the screen.
The first button from the left and the "Light” symbol on it allows you to control
the entire lighting system connected to the panel inside and outside the
caravan. The button second from the left and with the "+/- Light” symbol on it
provides access to the menu where the light intensity (dimmer) of the lightings
in the caravan is adjusted. The third button from the left with the "Lightning”
symbol provides access to the menu with information about the electric and
solar panel of the caravan. The fourth button from the left and the "Water
Drop” button on it provides access to the menu where the status of clean/dirty
water tanks of the caravan, booster, frost protection
CRAWLER
Model: TRC 458
Version: EN.1.00.422
25
Lighting Menu
The lighting menu is accessed by pressing the button with the "Light” symbol
on the main screen. The following menu will appear on the screen when the
screen is first opened.
Dimmer Menu
The dimmer control menu is accessed by pressing the button with the "+/-
Light” symbol on the main screen. There are three zones in the dimmer
menu. There are two buttons "+” and "-” for each zone. The control of the
light intensity of the zones is done from this menu.
It is used to decrease and increase the brightness of the lighting system of
the relevant area.
Circular buttons indicate the position of the lights inside the caravan. You can
turn the light on by pressing the white button of the area you want to turn on,
and turn it off by pressing the black button.
Water Menu
The Water Control menu is accessed by pressing the button with the "Water
Drop” symbol on the main screen. When you enter the menu, a page appears
as seen in the image below.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
26
If the caravan is not going to be used, it is recommended that the tanks be
completely emptied and parked in winter, otherwise, there may be damage to
the tanks due to freezing. CRAWLER Company is not responsible for
malfunctions and damages that may occur due to freezing.
When the buttons in the Water Menu are active, they will appear in "green”
color, while inactive, they will appear as "white”. The booster is not active
when the system is first turned on. In order to be able to use the water system
in the caravan, the booster is activated after the system is turned on, if the
system is completely turned off and opened or reset, the booster will become
passive again, in which case it is necessary to reactivate the booster.
After the booster is activated, even if all the taps are closed, the booster can
continue to work for a while, this is due to the balancing of the pressure in the
pipe in the water system. If the boiler tank is empty, this will take a little longer.
After the booster is activated, when any faucet connected to the caravan is
opened, water will automatically start flowing.
When the dirty water tank is full, the booster will automatically turn off in order
to prevent overflow. In this way, any overflow situation that may arise from the
caravan installation is prevented.
When the dirty water tank reaches 75% level, the warning shown in the picture
below appears at the top of the water page, informing that the tank is full and
the booster will stop when the tank level reaches 100%. When the dirty water
tank reaches 100% full, the booster will shut down. In this case, in order to
restart the booster, the dirty water tank must be properly emptied by opening
the discharge valve.
As shown in the image, there is information about clean water on the left side
of the screen, and information about dirty water on the right.
There are two buttons in the middle of the screen. The button at the top
provides "Frost Protection” and the button at the bottom provides the
"Booster” control.
In winter, the frost protection system must be active at temperatures of 4°C
and below. Otherwise, if the tank is full, the water in the tank will freeze and
increase in volume, and the tank or the plumbing system may be damaged
depending on the increased water volume. Being half full of the tank can
prevent damage caused by freezing, but if the water freezes, the system will
become unusable. In cases of freezing, the booster should be turned off.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
27
Settings Menu
The Electric control menu is accessed by pressing the button with the "Wheel"
symbol on the main screen. In the settings menu, there are time and date
information and a group of buttons to set this information. In order to set the
time and date, there are two buttons for each number, plus and minus. It can
be brought to the desired value by using the digital plus and minus buttons to
be adjusted. The settings page is shown in the image below.
Electric Menu
The Electric Control menu is accessed by pressing the button with the
"Lightning" symbol on the main screen. The electricity page has a battery
icon and a solar panel icon. The battery icon represents the battery on the
caravan and shows the battery status as a percentage by coloring the inside
of the battery. In addition to the electricity menu, the instantaneous voltage of
the battery and the average current drawn per minute are shown. Values are
updated on average every minute. As the amount of current drawn per minute
increases, the remaining time decreases, and as the current drawn decreases,
the remaining time increases. The electrical page is shown in the image below.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
28
At the bottom of the screen there is a slider where the brightness of the screen
can be adjusted. The screen brightness can be brought to the desired value
by sliding the slider to the right and left.
The sensor on the Crawler Smart Panel measures the atmospheric pressure
instantly. These values can be accessed from the Settings Menu.
Low Voltage Mode and Warning
Crawler Smart Panel constantly monitors the battery status, performs various
measurements and ensures long-lasting and efficient use of the battery. Low
voltage protection is activated when the battery voltage drops below 10.5
voltage and the smart panel switches to battery protection mode. In this
mode, the power of all systems connected to the smart panel is cut off and
the warning in the image below appears on the screen. This warning stays on
the screen for 10 seconds and then the smart panel turns itself off.
In this case, the battery should be charged as soon as possible. If the battery
charge at the critical energy level drops further, the battery may be damaged
completely by chemical degradation or its lifespan may be shortened. Devices
connected to the caravan should not be used while there is this warning on the
screen. If there is a working device, it should be turned off or the caravan
should be connected to the charger using the charging cable. Otherwise, the
product is out of warranty.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
29
What to do when smelling gas?
Avoid ignition sources! For example extinguish all open flames, do not use
any electrical switches, mobile phones or radios in the vehicle, do not start
the engine of the vehicle, operate devices, do not smoke in the vehicle.
Open windows and doors.
Evacuate all persons from the vehicle.
Shut off gas cylinders or turn off gas supply from outside. The entire gas
system must be checked and repaired by qualified personnel!
You can only put the gas system back into operation after inspection and
repair!
TRC 458 Owner's Obligations
The owner of the caravan is responsible for using the device in accordance
with the rules.
Hoses should be checked regularly and replaced if worn.
When a new appliance is put into operation for the first time, smoke and odor
may develop for a short time. When the appliance is put into operation after a
particularly long standstill period, a slight smoke and odor may occur due to
dust or dirt.
It is recommended to run the appliance for a few minutes at the highest
power level and then to ensure that the room is well ventilated for self-
cleaning.
The air temperature should always be checked before adjusting the hot air
outlets.
Hot water can be dangerous if misused and can cause burns. Check the water
temperature before each shower or bath.
The waste gas double pipe should be checked regularly, especially after long
trips, for damage and the soundness of the connections, as well as the
device and chimney connections. In order not to cause any damage due to
splashing water while washing the vehicle, water should not be poured
directly into the chimney.
Diesel Heater
Heating Mode
The air circulated by the fan motor is heated in the boiler and transmitted to
the caravan. Working integrated with the diesel heater control unit, the heat
sensors inside the caravan detect the temperature of the intake air. If the
temperature of the intake air is below the temperature set in the control unit,
the heater continues to operate.
Setting Mode
In the setting mode, the fan motor speed and the fuel delivery capacity of the
dosing pump depend on the heating capacity. In the meantime, the spark plug
is deactivated.
Thermostat Range
In case of approaching the temperature set on the operating switch, the
heating capacity is reduced by the control unit. The speed of the fan motor and
the fuel delivery capacity of the dosing pump are reduced in direct proportion
if the temperature set at a minimum heating capacity is reached, the fuel
pumping process of the dosing pump is terminated and the combustion
process ends with the heater blowing its last.
Note
Throughout the thermostat range, the heater fan motor operates at idle speed,
providing indoor air circulation. In addition, a change to be made on the
operating switch is evaluated by the control unit and then activated.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
30
Truma Combi
Liquid gas heater The Truma Combi is a hot air heater with an integrated hot
water tank (10 liters). The burner works with fan support. In this way, it is
ensured that it works flawlessly while cruising. By activating the heating water
operation with the heater, both the space can be heated and the water can be
heated. If only hot water is needed, hot water operation can be activated.
During hot water operation, the water in the tank is heated with the lowest
burner stage. The burner turns off when the water temperature is reached. In
heating operation, the device automatically selects the required power level
depending on the operating mode and the temperature difference between the
current room temperature set in the control unit and the current room
temperature. When the boiler is full, the water is automatically heated together.
The water temperature depends on the selected operating mode and the
heating power output.
If the temperature at the FrostControl automatic safety/drain valve is about 3
degrees, the valve opens and the boiler empties.
2.1 Safety Warnings
For safe and proper use, carefully read and observe the instructions for use
and save them for future use. Relevant applicable laws, directives and norms
must be observed. Non-observance of the regulations in the operating and
installation instructions can result in serious material damage or seriously
injure the health of persons. The user of the device is solely responsible for the
resulting damage. Only qualified and trained personnel (qualified personnel)
may install, commission or repair the product, following the installation and
operating instructions and the current accepted technical rules of the Truma
product. Specialized personnel are those who can perform the necessary
studies correctly and recognize possible hazards with the knowledge and
experience they have about Truma products and related standards due to
expert education and training.
2.2 What to do when smelling gas?
Avoid ignition sources! For example extinguish all open flames, do not use
any electrical switches, mobile phones or radios in the vehicle, do not start
the engine of the vehicle, operate devices, do not smoke in the vehicle.
Open windows and doors.
Evacuate all persons from the vehicle.
Shut off gas cylinders or turn off gas supply from outside.
The entire gas system must be checked and repaired by qualified personnel!
You can only put the gas system back into operation after inspection and
repair!
1 Digital or analog control unit (not pictured)
2 Room temperature sensors
3 Cold water connection
4 Hot water connection
5 Gas connection
6 Hot air outlets
7 Circulating air intake
8 Waste gas discharge
9 Combustion air intake
10 Electronic control unit
11 Water tank (10 liters)
12 Burners
13 Heat exchanger
14 Power electronic circuit
15 230 V Heaters
16 230V Overheat switch
17 FrostControl (safety/drain valve - optional on UK
version)
18 Safety/relief valve (UK version)
CRAWLER
Model: TRC 458
Version: EN.1.00.422
31
2.4 Actions in Case of Failure
In case of abnormal sound or smell, turn off the gas supply and Truma
Combi.
There is a risk of fire/explosion when attempting to operate a Truma Combi
that is damaged due to the vehicle being involved in an accident (e.g. drinks,
flooding leaks). A damaged Truma Combi boiler must be repaired or
replaced by a qualified personnel.
Have faults rectified immediately by qualified personnel.
After flashing (misfire), have the device and the exhaust gas system checked
by a specialist.
2.5 Maintenance/Repair/Cleaning
Equipment repair and cleaning should only be done by qualified personnel.
Maintenance, repair and cleaning by children is prohibited.
In the following cases, the warranty right and the right to claim liability are
eliminated.
Modifications to the device (including accessories),
Changes made in the waste gas installation and chimney,
Using spare parts and accessories other than Truma original parts, Failure to
comply with the assembly and operating instructions.
Rinse a new Combi and all hot/cold water hoses with potable water before
use, whether it is new or not used for a long time.
2.6 Heating Operation
In heating operation, the device automatically selects the required power
level depending on the temperature difference between the current room
temperature set in the control unit and the current room temperature. When
the boiler is full, the water is automatically heated together. The water
temperature depends on the selected operating mode and the heating power
output.
It can be used in 3 different types of energy specified in use.
During gas operation, the device automatically selects the required power
level.
For electrical operation, 900 W (3.9 A) or 1800 W (7.8 A) can be manually
preselected for power, depending on the campsite protection fuse. When the
power requirement is higher (e.g. when heating or the outside temperature is
very low), gas or mixed operation should be selected to ensure sufficient
heating power. 230 V electrical operation is preferred when the power demand
is low (e.g. to maintain room temperature) during mixed operation. The gas
burner only switches on at high power demand, ie it turns off before heating.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
32
2.7 Hot Water Operation (Only when the boiler is full)
Gas operation or electric operation 230 V is used for the hot water pipes. The
water temperature is set as ECO for 40 °C and HOT for 60 °C. During gas
operation, the water in the chamber is heated with the lowest burner stage.
The burner turns off when the water temperature is reached. For electrical
operation, the power can be manually selected as 900 W (3.9 A) or 1800 W
(7.8 A) according to the protection fuse in the campsite. Mixed operation is not
possible. In this setting, the device automatically selects electrical operation. If
the voltage supply to 230 V is limited or interrupted, the heater automatically
switches to gas operation.
2.8 Operating Instructions
Before commissioning, carefully read the safety warnings and operating
instructions and strictly follow the instructions!
2.8.1 Display and Control Elements
Truma Plus VarioHeat
1= Indicator
2= Status line
3= Menu line (top)
4= Menu line (bottom)
5= 230 V mains voltage display (current used in the country)
6= Timer display
7= Settings / Values
8= Rotary/ push button
9= Back key
With the rotary push button indicated with number 8, you can navigate between
the menus on lines 3 and 4, make selections and make various settings. The
button indicated with the number 9 can be used to return from any menu.
Target values and parameters can be selected, changed and saved by
pressing the rotary push button, indicated by the number 8. The selected menu
items flash.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
33
Pressing button 8 for a long time enables the main control function to be
turned on and off.
Counter-clockwise rotation
- The menu moves from right to left.
- Values are decremented (-).
Touching
- A selected value is inherited (saved).
- Selection of menu item, change to setting
level.
The time information and the set room temperature are displayed alternately
on the screen.
Turning On / Off
Touch button 8 to open. The previously set values/operating parameters are
reactivated after the device is switched on.
Press button 8 for more than 4 seconds to turn it off. Shutdown of the Truma
CP plus VarioHeat control unit may be delayed by several minutes due to the
internal subsequent operation of the heating or air conditioning system ("OFF"
is displayed during this time period).
Activating APP mode
Press button 8 for about 2 seconds until "APP" appears on the screen. Let go
of the rotary/push button.
The previously set values are saved.
Back button
When the back button 9 is pressed, it returns from a menu and the settings
made in that menu are cancelled. In other words, previously valid values are
preserved.
First commissioning
A few seconds after the Truma CP plus VarioHeat control unit is connected to
the power supply, a start screen appears.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
34
Turning off APP mode
If new values are transferred via the Truma App or the infrared remote
control of the air conditioning system, the APP mode is switched off. If the
Truma CP plus VarioHeat control unit is activated by pressing the rotary /
push button. The previously set values are taken over for the new operation,
the APP mode is turned off.
Changing the room temperature
Select the room temperature setting icon in the menu line number 3 with the
button number 8.
Press button 8 to switch to the setting level.
Select between heating (HEATER), air conditioning system (AC) with the
rotary / push button depending on the device connected.
Click on button 8 to confirm the selection.
Bring the button number 8 to the desired temperature by turning it to the right
and left.
Click on button 8 to confirm the value.
Heater Adjustable temperature range 5 - 30 °C (in 1 °C steps) a= Heater on
- Symbol is on, symbol flashes
CRAWLER
Model: TRC 458
Version: EN.1.00.422
35
if the room temperature has not been reached yet. It is essential that the
temperature range is selected below 5 °C (OFF) in order to turn off the
heater.
Choosing the energy type
Select the energy setting icon on the 3rd menu line with the 8 numbered
button.
a = GAS = Truma VarioHeat heats in gas operation.
b=MIX 1=Truma VarioHeat heats in gas operation. Truma E-Kit heats with
900 W.
c=MIX 2=Truma VarioHeat heats in gas operation. The Truma E-Kit heats
with
a maximum of 1800 W.
d= EL 1= Truma E-Kit heats with 900 W.
e= EL 2= Truma E-Kit heats with a maximum of 1800 W.
Selecting the fan stage
Select the fan icon on the 3rd menu line with the 8 numbered button.
Press button 8 to switch to the setting level.
Bring the button number 8 to the desired setting level by turning it to the right
and left. Click on button 8 to confirm the selection.
Press button 8 to switch to the setting level.
Bring the button number 8 to the desired setting level by turning it to the right
and left.
Click on button 8 to confirm the selection.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
36
2.8.2 Setting the timer
Danger of poisoning by exhaust gases
The activated timer also starts the heater when the vehicle is parked. Exhaust
gas from the heater can cause poisoning in closed spaces (e.g. garage,
workshop).
If the vehicle is parked indoors:
Cut off the fuel supply (gas) to the heater.
Switch off the Truma CP plus VarioHeat control unit (see "On / Off") to
prevent the heater from being reactivated by the Truma App or the timer.
Only use the timer of the Truma CP plus VarioHeat control unit to precisely
set the start and end time of the desired range when operating air
conditioning systems.
If the timer is ON, it is necessary to deactivate the timer first. If the timer is
not active (OFF), it is shown in the menu.
Select the timer setting symbol in the 4th menu line with the 8 button.
Switch to the setting level by touching it.
- = OFF= Fan Off (Can only be selected if there is no device running.)
a= VENT1= Circulated air, if no device is running. The number of cycles can
be selected in 10 steps.
b= AUTO= Automatic adjustment of the fan is adjusted depending on the
heating power / optimized to the current heating demand.
c= BOOST2= Fast room heating Can be used if the difference between the
selected and current room temperature is greater than 10 °C. Not available in
electronic operation (ELI, EL2).
d= NIGHT= Very quiet fan operation. The heater only works at partial load, it
may not reach the set room temperature if necessary (depending on vehicle
size and outside temperature). Only available in gas operation (GAS).
May cause higher engine wear depending on frequency of use. A quick step
change (on the stand-by display) is possible via button 8.
Electric current, noise level and engine wear are higher in the "BOOST" fan
stage.
When the Combi is switched on, the fan level selected in the previous
heating operation is displayed in the 2nd status line of the room temperature
setting. The default setting is "AUTO".
CRAWLER
Model: TRC 458
Version: EN.1.00.422
37
After confirming the time, the minute segment will flash.
Set the minute value to the desired value by using the button number 8.
When the minute value reaches the desired value, confirm the minute by
clicking the 8 button.
24 hour mode
12 hour mode
Entering the start time
Set the hour and then the minute with the number 8 button.
24 hour mode
12 hour mode
If the start / end time has passed at the time of entry, the operating parameters
will only be valid when the next start / end time is reached. Until then, the
operating parameters set apart from the timer are valid.
The hour is flashing when the screen is first turned on. Swipe left and right
using button 8 and set the clock to the desired value.
When the time reaches the desired value, confirm the time by clicking on the
8 button.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
38
Setting the room temperature
Depending on the device connected, use button 8 to choose between
heating (HEATER), air conditioning system (AC) or automatic air conditioning
(AUTO) (see fig. "Changing the room temperature" on page 18).
Click on button 8 to confirm the selection.
Select the room temperature you want with the button 8.
Click on button 8 to confirm the value.
Selecting the fan stage
Select the desired fan level with the 8 button. Click on button
8 to confirm the selection.
Select energy type (HEATER only)
For detailed information, see "Selecting the energy type", page 19, select the
energy type you want with the button number 8.
Click on button 8 to confirm the selection.
Activating the timer (ON)
Select the desired fan level with the 8 button.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
39
You can navigate between the settings shown below in the menu by using
the 8 button.
When the desired setting is reached, it can be selected by clicking the 8
button.
While in the selected setting, the selected setting is brought to the desired
value by sliding it to the right and left with the 8 button.
You can go back with the button number 9.
Calibration of the room temperature sensor of the heater
(OFFSET)
The room temperature sensor of the connected heater can be adapted to the
installation situation of the sensor. Adjustment can be made in 0.5 °C steps
in the range of 5 °C to -5 °C.
Example:
Set room temperature 23 °C OFFSET= -1 °C
Nominal value for heater = 22 °C
Click on button 8 to confirm the selection.
The timer remains active (OFF) for days until deactivated. If the timer is
programmed and active, the timer symbol will flash.
Deactivating the timer (OFF)
Press button 8 to switch to setting level.
Deactivate the timer with button 8. (OFF)
Click on button 8 to confirm the selection.
2.8.3 Service menu
It is located on the right side of menu number 4.
The menu is selected by clicking the 8 button.
Standard setting: 0 °C (Celsius). °C/°F temperature display Selection of °C
(Celsius) or °F (Fahrenheit) temperature display.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
40
Standard setting: 24 hour mode.
Changing the language
Selection of the desired language (German, English, French, Italian).
Standard setting: °C (Celsius).
Changing the backlight
Changing the backlighting of the Truma CP plus VarioHeat control unit in 10
steps.
Standard setting: English
Displaying the version number
Display the version number of the heater, air conditioning system, Truma
iNet Box and Truma CP plus VarioHeat control unit.
Example:
H 1.20.01 - H= Device; 1.20.01= Version number
12/ 24 hour mode
Display of time in 12 hour (a.m., p.m.) / 24 hour modes.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
41
Resetting
Select "RESET" with the 8 button.
Click on button number 8.
"PR SET" appears on the screen.
Click on button 8 to confirm.
Device
P=Truma CP plus VarioHeat control unit
L=Truma CP plus VarioHeat CI-Bus control unit
A= Air conditioning system
H= Truma VarioHeat
T= Truma iNet Box
E= Truma E-Kit
Standard setting (RESET)
The reset function resets the Truma CP plus VarioHeat control unit to factory
settings. All settings are deleted. Newly connected devices are detected and
stored in the control unit.
Turn on the voltage supply.
12 V= for Truma CP plus VarioHeat, Truma VarioHeat and Truma E-Kit control
unit and for 230 V air conditioning systems and Truma E-Kit.
After confirming, the Truma CP plus VarioHeat control unit is started. During
this process, "INIT .." is displayed on the screen.
Special indicators
Mains voltage 230 V available
The symbol indicates that the connected heating and/or air conditioning
system has a mains voltage of 230 V (the current used in the country).
CRAWLER
Model: TRC 458
Version: EN.1.00.422
42
Energy type indicator
Energy type in heating operation e.g. gas (a) is displayed (see "Selecting the
energy type" on page 19)
Infrared (ER) remote control (Air conditioning
system)
When a command is received from the infrared remote control of the air
conditioning system, "ER" is displayed on the screen.
Truma App with iNet Box
When a command is received from a mobile device with the Truma APP
application on it, "APP" is displayed on the screen.
External control unit (CI-BUS)
When a command is received from an external control unit with CI-BUS, "CI"
is displayed on the screen.
The Truma CP plus VarioHeat CI-BUS control unit is only a special model
fitted at the factory.
2.8.4 Warning / Fault
Warning
If the operating parameter is found outside of my target range, the Truma CP
plus VarioHeat control unit immediately switches to the "Warning/Fault" menu
level and the fault code of the fault is displayed. With the help of
troubleshooting instructions, the cause of the warning in question can be
determined and eliminated. Error and malfunction codes are shown at the end
of the Truma combi document under the topic Truma CP plus VarioHeat Error
and malfunction codes.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
43
Returning to the setting level
Click button number 8 or press backspace. If the screen is in Stand-by mode,
tapping activates the backlight and the warning can be confirmed by clicking
the screen again.
The device concerned remains in operation, if possible. If the operating
parameter is again within the target range, the symbol turns off automatically.
In the event of a fault, the Truma CP plus VarioHeat control unit immediately
switches to the "Warning / Fault" menu level and the fault code of the fault is
displayed: With the help of fault finding instructions, the said fault can be
detected and rectified. Error and malfunction codes are shown at the end of
the Truma combi document under the topic Truma CP plus VarioHeat Error
and malfunction codes.
Reading the warning error code
The error code can be called again after the
warning is acknowledged:
- Select the number one symbol seen in the
picture with the number 8 button.
- Click on the symbol with the number 8
button. The error code of the alert will be
displayed.
E= Error 12= Error code H= Device
H= Truma VarioHeat
A= Air conditioning system
E= Truma E-Kit
Cause fixed / Back to setting level
Click on button number 8. If the screen is in Standby mode, tapping activates
the backlight and the fault must be confirmed by tapping the screen again.
W= Warning 42= Error code H= Device
H= Truma VarioHeat
A= Air conditioning system
E= Truma E-Kit
Fault
CRAWLER
Model: TRC 458
Version: EN.1.00.422
44
Disposal of waste
The device must be disposed of in accordance with the administrative
regulations applicable in the country of use. National legislation (e.g. Scrap
Vehicles Regulation in Germany) must be observed.
2.9 Room temperature sensors
To measure the room temperature, the vehicle is equipped with an external
room temperature sensor. The location of the sensor is determined by the
vehicle manufacturer according to the vehicle type.
If necessary, the relevant device will be restarted automatically.
This may take several minutes due to the internal after-work of the
connected devices.
If the cause of the fault is not remedied, the fault will reappear and the control
unit will switch back to the "Warning/Fault" menu level.
Cause not fixed / Back to setting level
Press the back button.
In this case, the fault in the Truma CP plus VarioHeat control unit is not
acknowledged and the warning symbol remains. The device remains in the
fault state. Other connected devices can be controlled.
Reading the fault error code
After the fault has been acknowledged, the fault code can be recalled:
- Select the warning symbol with the 8 button.
- Click on button 8 and the current state of the fault is read.
Maintenance
The Truma CP plus VarioHeat control unit is maintenance-free. To clean the
front, use a non-scratching cloth dampened with water. If it cannot be cleaned
in this way, use a neutral soap solution.
The temperature setting in the control unit depends on the individual heat
requirement and the vehicle model and must be made individually.
2.10 Safety / relief valve
FrostControl
(Safety / drain valve with integrated anti-freeze / optional in UK version)
FrostControl is a non-electric safety / drain valve. When there is a danger of
freezing, the boiler automatically empties the water in it via a drain port. When
high pressure occurs in the system, pressure balancing is performed
intermittently via the safety valve.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
45
Closing the safety/drain valve
Make sure that the rotary switch is in the "operation" (position a) position,
parallel to the water supply and inside.
Close the safety/drain valve by pressing the push button. The push button (b)
should go in on the "off" position. However, when the temperature at the
safety/drain valve is above approx. 7 °C, the safety/drain valve can be closed
manually using the push button (position b) and the boiler can be filled. Truma
supplies a heating element (item no. 70070- 01) which is fitted inside the
FrostControl and fixed with a safety plate as an accessory. This heating
element heats the FrostControl to approx. 10 °C when the Truma Combi is on.
The boiler can thus be filled after a short time, regardless of the temperature
at the installation site.
a= "operating" position of the rotary switch
b= Push button "off" position
c= Push button "dump" position
d= Drain opening (outward from the vehicle floor)
Opening the safety/relief valve
Turn the rotary switch 180° until it engages, the push button pops out
(position c). The water in the boiler flows out via the discharge opening (d).
To ensure a safe flow of water, dirt accumulation (snowy, mud, ice,
brushwood, etc.) must be prevented at the discharge opening
(d) of the FrostControl! No warranty can be claimed for damage caused by
freezing!
CRAWLER
Model: TRC 458
Version: EN.1.00.422
46
Automatically opening the safety/relief valve
When the temperature at the safety/drain valve is below approx. 3 °C, the
safety/drain valve opens automatically, the push button pops out (position c).
The water in the boiler flows out via the discharge opening (d).
Safety / relief valve
The safety/relief valve automatically compensates for pressure when high
pressure builds up in the system. In this case, the water is discharged
outwards intermittently via the discharge opening. This safety/drain valve does
not protect the water tank from damage by freezing.
Opening the safety/relief valve
Move the lever vertically to the (c) position. The water in the boiler flows out
via the discharge opening (d). To ensure a safe flow of water, the accumulation
of dirt (snowy, mud, ice, brushwood, etc.) must be prevented at the discharge
port (d) of the safety / drain valve! No warranty can be claimed for damage
caused by freezing!
Closing the safety/drain valve
Move the lever horizontally to the (a) or (b) position.
2.11 Filling the boiler
Make sure that the safety / drain valve is closed (see section "Closing the
safety / drain valve"). If the temperature in the FrostControl is below approx. 7
°C, first switch on the heater to warm up the installation space and the
FrostControl. After a few minutes, when the temperature in the FrostControl
rises above 7 °C, the safety / drain valve can be closed.
Turn on the power to the water pump (main switch or pump switch).
a= Lever in "Operating - off" position
b= Lever in "Operating - off" position
c= Lever in "Drain" position
d= Drain opening (outward from the
vehicle floor)
CRAWLER
Model: TRC 458
Version: EN.1.00.422
47
Turn on the hot water taps in the kitchen and bathroom (set the water regulator
or the single lever faucet to the "hot" position). Keep the faucets open until the
air in the boiler is completely emptied and the water flows uninterruptedly.
Even if only the cold water installation will be operated without a boiler, the
boiler will be filled with water. In order to prevent damage due to freezing, the
boiler should be emptied via the safety / drain valve even if it is not used.
In case of frost, the filling process may not take place because the water is
frozen. The boiler can be defrosted by short-term operation (maximum 2
minutes). Frozen pipes can be thawed by heating the interior.
When connecting to a central water supply (country or city connection), a
pressure reducer must be used to prevent pressure above 2.8 bar in the
boiler.
2.12 Emptying the boiler
Attention: If the motorhome / caravan will not be used during the frosty period,
the boiler must be emptied!
Turn off the power to the water pump (main switch or pump switch).
Turn on the hot water taps in the kitchen and bathroom.
Place a suitable container (10 liters) under the drain port (d) of the safety/drain
valve to control the flowing water.
Open the safety / drain valve (see section "Opening the safety / drain valve").
The boiler is emptied directly to the outside via the safety/drain valve. Check
whether the water in the boiler (10 liters) is completely drained into the
container via the safety / drain valve.
No warranty can be claimed for damage caused by freezing!
2.13 Commissioning
Combi E
(in conjunction with the CP plus control unit) The interior can be heated with
or without water in gas, electric and mixed operation, depending on the
operating position.
Check whether the protection fuse of the electricity supply in the campsite is
sufficient for the 900 W (3.9 A) or 1800 W (7.8 A) power set via the energy
selection switch.
The cable reel must be fully opened to prevent the power supply cable from
overheating.
Check if the chimney is unblocked. Be sure to remove everything that will
cover it, such as a lid.
Open the gas cylinder and the quick shut-off valve on the gas supply pipe.
If necessary, fill the boiler with water (see section "Filling the boiler").
Turn on the device with the control unit.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
48
Efforts to be done by the user
Clean the installation site at least once a year.
The safety/drain valve must be operated regularly (at least 2 times a year) to
remove limescale deposits and ensure that it is not blocked.
Warnings for cleaning, build-up dirt and maintenance
We recommend that you use the appropriate maintenance products available
in the market for boiler cleaning, cleaning the dirt accumulated in the boiler
and maintenance of the boiler. Chlorinated products should not be used.
The chemical method for combating microorganisms in the device can be
supported by regularly heating the water in the boiler to 70 °C.
Only in conjunction with the Combi E, CP Plus control unit - select the "gas
operation" operating mode on the CP plus control unit.
Set the water temperature to 60 °C.
Turn on the device.
The burner switches off when the water in the boiler reaches 60 °C. The device
must remain in operation for at least 30 minutes and hot water should not be
used. The residual heat in the heat exchanger heats the water up to 70 °C.
2.14 Turning off
Turn off the heater with the control unit.
The shutdown process may be delayed by several minutes due to the
internal after-runs of the heater.
If the device will not be used for a long time, close the quick shut-off valve on
the gas supply pipe and the gas cylinder.
In cases where there is a risk of freezing, always drain the water!
2.15 Maintenance
Maintenance, repair and cleaning by children is prohibited. Work to be done
by specialists. Have the device checked by specialist for contamination and
have it cleaned if necessary.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
49
2.16 Fuses
Electrostatic charge can cause damage to the electronic system. Equalize the
potential before touching the electronic system!
Fuse and mains connection lines must only be replaced by a qualified
person!
Before opening the electronic circuit cover, the device must be disconnected
from the mains.
The fuse is located in the power electronic circuit (14) under the electronic
circuit cover.
This sensitive fuse should only be replaced with a fuse of the same
construction: 10A, fast, breaking capacity "H".
Fuse 230 V
(Combi E)
CAUTION: Danger to life due to electric shock when replacing
the fuse or power supply lines.
Overheat protection 230 V (Combi E)
The 230 V heating operation has a mechanical overheating switch. For
example, if the 12 V voltage supply is interrupted during operation or during
the following operation, temperatures in the device may cause the overheating
protection to trip.
Water is flowing / dripping
from the discharge port of
the safety / drain valve.
The water pressure is too high. / Check the
pump pressure (maximum 2.8 bar). When
connecting to a central water supply (country or
city connection), a pressure reducer must be
used to prevent pressure above 2.8 bar in the
boiler.
FrostControl is turned on
after the heater is turned
off.
At temperatures below approx. 3°C,
FrostControl switches on automatically / Turn
on the heating / If the heating operation is not
activated, FrostControl can only be switched off
at temperatures above approx. 7 °C / Use the
heating element for FrostControl.
Unable to close
FrostControl.
With FrostControl the temperature is below
approx. 7 °C / Turn on the heating / If the heating
mode is not activated, FrostControl can only be
switched off at temperatures above approx. 7
°C.
The rotary switch is not in the "Operation"
position. / Turn the FrostControl rotary switch to
"Operation" and then press the rocker switch
until it engages.
2.17 Troubleshooting instruction (Water supply)
Error
Cause / Solution method
Extremely Long Warm-up
time
The water tank is chalky. / Descale the water
system. (See the Maintenance section.)
Water is flowing. Boiler
cannot be filled.
The safety/drain valve is open. / Close the
safety / drain valve.
The boiler cannot be
drained even though the
safety/drain valve is open.
The discharge port of the safety / relief valve is
closed. / Check the hole for dirt (snowy, mud,
ice, brushwood, etc.) and clean if necessary.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
50
Resetting the overheating protection Wait for the heater to cool down, remove
the connector cover and press the Reset button.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
51
2.18 Cases out of warranty
Warranty claims cannot be claimed in the following cases:
Using the device incorrectly, improperly, incorrectly, carelessly or contrary to
its intended use.
Improper installation, assembly or commissioning contrary to the information
described in the operating and assembly instructions.
Incorrect operation or use of the device contrary to the information described
in the operating and assembly instructions, especially non-compliance with the
maintenance and cleaning instructions and ignoring the warnings.
Installation, repair or necessary interventions are not performed by authorized
business partners.
Consumables, wear parts and natural wear.
Equipping the device with spare and complementary parts or accessories that
are not original parts manufactured by the manufacturer or not approved by
the manufacturer. This is especially true in the device with a control system
operating in the network if the control units and software are not approved by
Truma or the Truma control unit (e.g. Truma CP plus, Truma iNet Box) is not
used only for Truma devices or for Truma approved devices.
Foreign substances (e.g. oil, softeners in gas), damage caused by chemical
or electrochemical effects in water, or contact with unsuitable substances (e.g.
chemical products, flammable substances, unsuitable cleaning agents).
Damages caused by abnormal environment or operating conditions unfamiliar
to the subject.
Damages caused by force majeure or natural disasters and other effects for
which Truma cannot be held responsible.
Damages caused by incorrect transportation.
Changes made by the end customer or third parties to the device, especially
to the waste gas installation and chimney, including spare and complementary
parts or accessories and their installation.
2.19 Truma CP plus VarioHeat Error and fault codes
Warnings
The crane is a very powerful machine. Be very careful and heed all warnings.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
52
Things to do before uninstalling:
Check the wire / synthetic rope.
Lay a rescue damper on the rope near the hook end.
Set the anchor point.
Tune the vehicle engine.
Install the clamp and hook.
Begin lifting with crane.
Make sure the connection is secure.
Disconnect the remote control.
General rules
Check safety and environmental conditions before and during use.
Use only the correct grade of wire/synthetic rope in construction and strength.
Check for damage and/or defects before use.
Do not use an unsuitable hook and clasp block for the rope.
Do not use the crane as a hoist or a crane for lifting and transporting people.
Crane
The crane is rated at the first layer of wire/synthetic rope on the drum for
intermittent periodic duty.
A minimum of (5) steel wire rope wraps and ten (10) synthetic rope wraps
around the drum are required to support the rated load.
Keep away from crane, rope, hook and dovetail during operation.
Wire/synthetic rope can break without warning. Always keep a safe distance
from the crane and rope when under load. Failure to adequately align, support,
or attach the crane to a suitable mounting base may result in a loss of
performance efficiency or damage to the crane, wire/synthetic rope, and
mounting conduit.
Things to do before using the crane
Connect the remote control.
Disengage the clutch function.
Pull the wire/synthetic rope to the attachment point.
Activate the clutch function.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
53
Always wear leather gloves when handling wire/synthetic rope.
The rope must be wound according to the drum rotation label or refer to the
instruction manual.
Correct
Wrong
Bottom Winding
Top Winding
CRAWLER
Model: TRC 458
Version: EN.1.00.422
54
Victron Energy Battery
- Gel battery is a system that stores energy and is used when required.
- The gel battery has a very wide discharge feature. It does not cause
deterioration after charging. It is shock resistant.
- The charger to be used for charging the gel battery is very important. The
temperature and humidity of the environment are very important while the
charger allows the battery to be charged.
- The charger must be suitable for the gel battery. A bad or unsuitable
charger can cause the battery to fail.
- Victron Energy Battery is suitable for high current discharge and charging
operations due to its very low internal resistance.
- Battery Gel offers the best deep cycle durability and provides a longer
service life. The use of completely pure materials and lead calcium grids
reduces the tendency of the GEL to self-discharge, delaying their discharge
even when not charged for a long time.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
55
Schmid Solar Panel 325w & Regulator
- The electricity produced by the solar panel installed on the roof of the
caravan is stored in the batteries via the energy charge control unit.
- Then, the energy in the batteries is converted to 220 volts by means of
an inverter, so that the devices you want to use in the caravan work.
- The power output of the solar panel is within positive (+) tolerance.
- It is automatically classified according to the power output values.
- The Solar Panel is resistant to salt water and ammonia. It can be used in
corrosive environments in harsh natural conditions.
- As it is an environmentally friendly system, high efficiency is ensured.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
56
Thule Electric Step
- In order to use the electric step, press and hold the button on the bottom
left of the entrance to the down direction.
- Press and hold upwards to turn it off.
- It makes it easy to use at night thanks to the rounded corners that glow in
the dark.
- The steps are made of corrugated anodized aluminium.
- Inside the caravan there is a switch for the connection of a warning lamp.
As standard, the step makes it impossible to get out.
- For maximum visibility to be clearly visible in all conditions, each
motorized slide step can be equipped with the optional Thule LED Kit for
additional lighting.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
57
When commissioning, decommissioning and operating the Mover XT / XT2,
care must be taken to ensure that no hair, clothing or moving parts of the body
are between rotating parts.
During maneuvering, the distance between the radio remote control and the
middle of the caravan should not exceed 10 m.
Engage the parking brake in the event of a malfunction.
To avoid tipping the caravan, the drawbar should point down (downhill) when
maneuvering on slopes.
After manoeuvring, always apply the parking brake first. Separate the drive
rollers from the tires and block the wheels (especially on slopes!). The Mover
XT/ XT2 is not suitable for use as a parking brake for a parked caravan.
Always protect the remote control from unauthorized access (especially from
children).
Never tow the caravan with the drive rollers installed as this can damage the
tires, towing vehicle and drive assemblies.
All wheels and tires on the caravan must be the same size and type.
When using a jack, the Mover XT /XT2 should not be used as a jacking point
as it may damage the drive assembly.
Turn off the mover button after maneuvering, otherwise the battery will be
discharged.
Inspect the system for damage prior to use. If the system is damaged, it
should not be used.
Mover
Safety Instructions
It can only be installed by competent and trained persons (experts).
This appliance can be used by children over 8 years old. It can be used by
disabled or inexperienced persons only if supervised or by persons who do not
take the risks and the safe use of the device. Children should not be allowed
to play with the appliance.
Before using the Mover XT / XT2 outdoors for the first time, demo the remote
control and the Mover XT /XT2 to become familiar with the functions of the
following.
Before each use of the Mover XT / XT2, inspect the tires and remove any sharp
stones and similar objects between the drive rollers and the wheel.
The side slide switch (ON/OFF) on the remote control also functions as an
"Emergency Stop Switch". In any emergency, immediately turn the side slide
switch to the "OFF" position, (abnormalities, uncontrolled behavior of the
manoeuvre)
Nobody should be in the caravan during the operation.
No one (especially children) should be inside the turning and range of motion
(manoeuvring range).
CRAWLER
Model: TRC 458
Version: EN.1.00.422
58
Technical Specifications
Body: Aluminium
Insulation: Ceramic Based Internal Heat Insulation
Wheel Dimensions: 285/75/R16, Rim: 6x139.7
Coupling: With Brake and Reverse Maneuverer
Chassis: Cataphoresis Coating
Suspension: Independent Swing System Suspension, 4 Shock Absorbers
Length: 4.580 mm
Width: 2,000 mm
Height: 2.450 mm
Weight: 865 kg (with Standard Equipment)
CRAWLER
Model: TRC 458
Version: EN.1.00.422
59
Electric scheme
CRAWLER
Model: TRC 458
Version: EN.1.00.422
60
Care Instructions
Cleaning
The caravan should be washed as soon as it gets dirty, especially in winter
months when salt and moisture on the roads can easily start to rust.
The caravan should be washed as follows.
Wash the entire caravan with plenty of water until the dirt is softened.
Do not spray the water directly on the locks.
Wash the vehicle with a sponge using plenty of water with or without detergent.
If the vehicle is very dirty, you can wash the vehicle first with a cold degreasing
agent. However, you should only perform this operation in a place with a waste
water separation feature. Take care not to expose cold oil directly to the sun
and the paint to not get hot from the sun or the engine is still not hot. Sunlight
and heat can cause permanent damage. Consult CRAWLER about this.
Dry the caravan with a clean and soft cloth.
You can clean muddy areas with warm soapy water.
Suitable detergent
Clean bird droppings from the paint as soon as possible. Chemical substances
in bird droppings can affect and fade the paint in a very short time. It is not
possible to restore the faded paint by polishing.
Automatic Washing
The simplest and quickest way to wash your caravan is to take it to an
automated washing facility. However, keep in mind that washing in an
automatic washing facility cannot replace a thorough hand washing.
The brushes of the automatic washing plant may not reach all parts of the
caravan effectively. We recommend hand washing the caravan in the first
months.
After washing the caravan: Always check the brakes so that moisture and
corrosion do not affect or damage the brake pads!
Cleaning the floor
Removing stains on fabric upholstery
CRAWLER
Model: TRC 458
Version: EN.1.00.422
61
For soiled fabric upholstery, it is recommended to use a special cleaning agent,
available from your CRAWLER dealer. Other chemicals may damage the fire
resistance of the flooring.
Never try to remove the stain by scraping or rubbing.
Never use strong stain remover.
Wash with mild soap and warm water.
Repairing paint damage
Paint
The electrostatic paint on the caravan is a scratch resistant paint. In order to
repair the scratches that will occur over time on the caravan, a retouching
process is applied with paint with the same color code.
Below are the most common types of paint damage you can repair:
Minor stone, branch nicks and scratches
Damages around the outer shell
CRAWLER
Model: TRC 458
Version: EN.1.00.422
62
Warranty Text
1. The warranty period starts from the caravan delivery date.
The outer body warranty is five (5) years and the component warranty is two
(2) years. Accessories and other options are under the manufacturer's
warranty.
2. The entire caravan, including all its parts, is under our company's warranty.
3. Failures caused by the use of the caravan contrary to the terms in the user
manual are not covered by the warranty.
4. You can apply to CRAWLER for any problems that may arise regarding the
Warranty Certificate.
5. If the caravan fails within the warranty period, the time spent in repair is
added to the warranty period. The caravan's repair time is maximum 20
working days. This period starts on the delivery date of the vehicle to the
service station or, in the absence of a service station, to one of the authorized
dealer, dealer, agency, representative, importer or manufacturer of the vehicle.
6. Equipment and options used in the caravan are covered by the
manufacturer's or distributor's warranty.
7. In case of intervention to or modification of the vehicle and the equipment
inside the vehicle other than the CRAWLER service, the related and affected
equipment will not be covered by the warranty.
CRAWLER
Model: TRC 458
Version: EN.1.00.422
63
VENDOR’S;
Title:
Address:
Phone:
Invoice Date and No:
Sign (Seal):
CRAWLER
WARRANTY FORM
Company: Crawler CARAVANS
HQ Address: Holzheimer Str. 12, 73037 Göppingen, Germany
Phone: +49 71613047623
E-mail: info@crawlercaravans.com
VEHICLE OWNER’S;
Name:
Address:
Phone:
E-mail:
Sign:
VEHICLE’S;
Model: TRC 458
Banderole and Serial No:
Delivery Date and Place:
Warranty Period:
Maximum Repair Time:
20 Work Days
